1 /** 2 ****************************************************************************** 3 * @file stm32f4xx_hal_gpio.h 4 * @author MCD Application Team 5 * @brief Header file of GPIO HAL module. 6 ****************************************************************************** 7 * @attention 8 * 9 * <h2><center>© Copyright (c) 2017 STMicroelectronics. 10 * All rights reserved.</center></h2> 11 * 12 * This software component is licensed by ST under BSD 3-Clause license, 13 * the "License"; You may not use this file except in compliance with the 14 * License. You may obtain a copy of the License at: 15 * opensource.org/licenses/BSD-3-Clause 16 * 17 ****************************************************************************** 18 */ 19 20 /* Define to prevent recursive inclusion -------------------------------------*/ 21 #ifndef __STM32F4xx_HAL_GPIO_H 22 #define __STM32F4xx_HAL_GPIO_H 23 24 #ifdef __cplusplus 25 extern "C" { 26 #endif 27 28 /* Includes ------------------------------------------------------------------*/ 29 #include "stm32f4xx_hal_def.h" 30 31 /** @addtogroup STM32F4xx_HAL_Driver 32 * @{ 33 */ 34 35 /** @addtogroup GPIO 36 * @{ 37 */ 38 39 /* Exported types ------------------------------------------------------------*/ 40 /** @defgroup GPIO_Exported_Types GPIO Exported Types 41 * @{ 42 */ 43 44 /** 45 * @brief GPIO Init structure definition 46 */ 47 typedef struct 48 { 49 uint32_t Pin; /*!< Specifies the GPIO pins to be configured. 50 This parameter can be any value of @ref GPIO_pins_define */ 51 52 uint32_t Mode; /*!< Specifies the operating mode for the selected pins. 53 This parameter can be a value of @ref GPIO_mode_define */ 54 55 uint32_t Pull; /*!< Specifies the Pull-up or Pull-Down activation for the selected pins. 56 This parameter can be a value of @ref GPIO_pull_define */ 57 58 uint32_t Speed; /*!< Specifies the speed for the selected pins. 59 This parameter can be a value of @ref GPIO_speed_define */ 60 61 uint32_t Alternate; /*!< Peripheral to be connected to the selected pins. 62 This parameter can be a value of @ref GPIO_Alternate_function_selection */ 63 }GPIO_InitTypeDef; 64 65 /** 66 * @brief GPIO Bit SET and Bit RESET enumeration 67 */ 68 typedef enum 69 { 70 GPIO_PIN_RESET = 0, 71 GPIO_PIN_SET 72 }GPIO_PinState; 73 /** 74 * @} 75 */ 76 77 /* Exported constants --------------------------------------------------------*/ 78 79 /** @defgroup GPIO_Exported_Constants GPIO Exported Constants 80 * @{ 81 */ 82 83 /** @defgroup GPIO_pins_define GPIO pins define 84 * @{ 85 */ 86 #define GPIO_PIN_0 ((uint16_t)0x0001) /* Pin 0 selected */ 87 #define GPIO_PIN_1 ((uint16_t)0x0002) /* Pin 1 selected */ 88 #define GPIO_PIN_2 ((uint16_t)0x0004) /* Pin 2 selected */ 89 #define GPIO_PIN_3 ((uint16_t)0x0008) /* Pin 3 selected */ 90 #define GPIO_PIN_4 ((uint16_t)0x0010) /* Pin 4 selected */ 91 #define GPIO_PIN_5 ((uint16_t)0x0020) /* Pin 5 selected */ 92 #define GPIO_PIN_6 ((uint16_t)0x0040) /* Pin 6 selected */ 93 #define GPIO_PIN_7 ((uint16_t)0x0080) /* Pin 7 selected */ 94 #define GPIO_PIN_8 ((uint16_t)0x0100) /* Pin 8 selected */ 95 #define GPIO_PIN_9 ((uint16_t)0x0200) /* Pin 9 selected */ 96 #define GPIO_PIN_10 ((uint16_t)0x0400) /* Pin 10 selected */ 97 #define GPIO_PIN_11 ((uint16_t)0x0800) /* Pin 11 selected */ 98 #define GPIO_PIN_12 ((uint16_t)0x1000) /* Pin 12 selected */ 99 #define GPIO_PIN_13 ((uint16_t)0x2000) /* Pin 13 selected */ 100 #define GPIO_PIN_14 ((uint16_t)0x4000) /* Pin 14 selected */ 101 #define GPIO_PIN_15 ((uint16_t)0x8000) /* Pin 15 selected */ 102 #define GPIO_PIN_All ((uint16_t)0xFFFF) /* All pins selected */ 103 104 #define GPIO_PIN_MASK 0x0000FFFFU /* PIN mask for assert test */ 105 /** 106 * @} 107 */ 108 109 /** @defgroup GPIO_mode_define GPIO mode define 110 * @brief GPIO Configuration Mode 111 * Elements values convention: 0xX0yz00YZ 112 * - X : GPIO mode or EXTI Mode 113 * - y : External IT or Event trigger detection 114 * - z : IO configuration on External IT or Event 115 * - Y : Output type (Push Pull or Open Drain) 116 * - Z : IO Direction mode (Input, Output, Alternate or Analog) 117 * @{ 118 */ 119 #define GPIO_MODE_INPUT 0x00000000U /*!< Input Floating Mode */ 120 #define GPIO_MODE_OUTPUT_PP 0x00000001U /*!< Output Push Pull Mode */ 121 #define GPIO_MODE_OUTPUT_OD 0x00000011U /*!< Output Open Drain Mode */ 122 #define GPIO_MODE_AF_PP 0x00000002U /*!< Alternate Function Push Pull Mode */ 123 #define GPIO_MODE_AF_OD 0x00000012U /*!< Alternate Function Open Drain Mode */ 124 125 #define GPIO_MODE_ANALOG 0x00000003U /*!< Analog Mode */ 126 127 #define GPIO_MODE_IT_RISING 0x10110000U /*!< External Interrupt Mode with Rising edge trigger detection */ 128 #define GPIO_MODE_IT_FALLING 0x10210000U /*!< External Interrupt Mode with Falling edge trigger detection */ 129 #define GPIO_MODE_IT_RISING_FALLING 0x10310000U /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ 130 131 #define GPIO_MODE_EVT_RISING 0x10120000U /*!< External Event Mode with Rising edge trigger detection */ 132 #define GPIO_MODE_EVT_FALLING 0x10220000U /*!< External Event Mode with Falling edge trigger detection */ 133 #define GPIO_MODE_EVT_RISING_FALLING 0x10320000U /*!< External Event Mode with Rising/Falling edge trigger detection */ 134 /** 135 * @} 136 */ 137 138 /** @defgroup GPIO_speed_define GPIO speed define 139 * @brief GPIO Output Maximum frequency 140 * @{ 141 */ 142 #define GPIO_SPEED_FREQ_LOW 0x00000000U /*!< IO works at 2 MHz, please refer to the product datasheet */ 143 #define GPIO_SPEED_FREQ_MEDIUM 0x00000001U /*!< range 12,5 MHz to 50 MHz, please refer to the product datasheet */ 144 #define GPIO_SPEED_FREQ_HIGH 0x00000002U /*!< range 25 MHz to 100 MHz, please refer to the product datasheet */ 145 #define GPIO_SPEED_FREQ_VERY_HIGH 0x00000003U /*!< range 50 MHz to 200 MHz, please refer to the product datasheet */ 146 /** 147 * @} 148 */ 149 150 /** @defgroup GPIO_pull_define GPIO pull define 151 * @brief GPIO Pull-Up or Pull-Down Activation 152 * @{ 153 */ 154 #define GPIO_NOPULL 0x00000000U /*!< No Pull-up or Pull-down activation */ 155 #define GPIO_PULLUP 0x00000001U /*!< Pull-up activation */ 156 #define GPIO_PULLDOWN 0x00000002U /*!< Pull-down activation */ 157 /** 158 * @} 159 */ 160 161 /** 162 * @} 163 */ 164 165 /* Exported macro ------------------------------------------------------------*/ 166 /** @defgroup GPIO_Exported_Macros GPIO Exported Macros 167 * @{ 168 */ 169 170 /** 171 * @brief Checks whether the specified EXTI line flag is set or not. 172 * @param __EXTI_LINE__ specifies the EXTI line flag to check. 173 * This parameter can be GPIO_PIN_x where x can be(0..15) 174 * @retval The new state of __EXTI_LINE__ (SET or RESET). 175 */ 176 #define __HAL_GPIO_EXTI_GET_FLAG(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__)) 177 178 /** 179 * @brief Clears the EXTI's line pending flags. 180 * @param __EXTI_LINE__ specifies the EXTI lines flags to clear. 181 * This parameter can be any combination of GPIO_PIN_x where x can be (0..15) 182 * @retval None 183 */ 184 #define __HAL_GPIO_EXTI_CLEAR_FLAG(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__)) 185 186 /** 187 * @brief Checks whether the specified EXTI line is asserted or not. 188 * @param __EXTI_LINE__ specifies the EXTI line to check. 189 * This parameter can be GPIO_PIN_x where x can be(0..15) 190 * @retval The new state of __EXTI_LINE__ (SET or RESET). 191 */ 192 #define __HAL_GPIO_EXTI_GET_IT(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__)) 193 194 /** 195 * @brief Clears the EXTI's line pending bits. 196 * @param __EXTI_LINE__ specifies the EXTI lines to clear. 197 * This parameter can be any combination of GPIO_PIN_x where x can be (0..15) 198 * @retval None 199 */ 200 #define __HAL_GPIO_EXTI_CLEAR_IT(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__)) 201 202 /** 203 * @brief Generates a Software interrupt on selected EXTI line. 204 * @param __EXTI_LINE__ specifies the EXTI line to check. 205 * This parameter can be GPIO_PIN_x where x can be(0..15) 206 * @retval None 207 */ 208 #define __HAL_GPIO_EXTI_GENERATE_SWIT(__EXTI_LINE__) (EXTI->SWIER |= (__EXTI_LINE__)) 209 /** 210 * @} 211 */ 212 213 /* Include GPIO HAL Extension module */ 214 #include "stm32f4xx_hal_gpio_ex.h" 215 216 /* Exported functions --------------------------------------------------------*/ 217 /** @addtogroup GPIO_Exported_Functions 218 * @{ 219 */ 220 221 /** @addtogroup GPIO_Exported_Functions_Group1 222 * @{ 223 */ 224 /* Initialization and de-initialization functions *****************************/ 225 void HAL_GPIO_Init(GPIO_TypeDef *GPIOx, GPIO_InitTypeDef *GPIO_Init); 226 void HAL_GPIO_DeInit(GPIO_TypeDef *GPIOx, uint32_t GPIO_Pin); 227 /** 228 * @} 229 */ 230 231 /** @addtogroup GPIO_Exported_Functions_Group2 232 * @{ 233 */ 234 /* IO operation functions *****************************************************/ 235 GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin); 236 void HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState); 237 void HAL_GPIO_TogglePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin); 238 HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin); 239 void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin); 240 void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin); 241 242 /** 243 * @} 244 */ 245 246 /** 247 * @} 248 */ 249 /* Private types -------------------------------------------------------------*/ 250 /* Private variables ---------------------------------------------------------*/ 251 /* Private constants ---------------------------------------------------------*/ 252 /** @defgroup GPIO_Private_Constants GPIO Private Constants 253 * @{ 254 */ 255 256 /** 257 * @} 258 */ 259 260 /* Private macros ------------------------------------------------------------*/ 261 /** @defgroup GPIO_Private_Macros GPIO Private Macros 262 * @{ 263 */ 264 #define IS_GPIO_PIN_ACTION(ACTION) (((ACTION) == GPIO_PIN_RESET) || ((ACTION) == GPIO_PIN_SET)) 265 #define IS_GPIO_PIN(PIN) ((((PIN) & GPIO_PIN_MASK ) != 0x00U) && (((PIN) & ~GPIO_PIN_MASK) == 0x00U)) 266 #define IS_GPIO_MODE(MODE) (((MODE) == GPIO_MODE_INPUT) ||\ 267 ((MODE) == GPIO_MODE_OUTPUT_PP) ||\ 268 ((MODE) == GPIO_MODE_OUTPUT_OD) ||\ 269 ((MODE) == GPIO_MODE_AF_PP) ||\ 270 ((MODE) == GPIO_MODE_AF_OD) ||\ 271 ((MODE) == GPIO_MODE_IT_RISING) ||\ 272 ((MODE) == GPIO_MODE_IT_FALLING) ||\ 273 ((MODE) == GPIO_MODE_IT_RISING_FALLING) ||\ 274 ((MODE) == GPIO_MODE_EVT_RISING) ||\ 275 ((MODE) == GPIO_MODE_EVT_FALLING) ||\ 276 ((MODE) == GPIO_MODE_EVT_RISING_FALLING) ||\ 277 ((MODE) == GPIO_MODE_ANALOG)) 278 #define IS_GPIO_SPEED(SPEED) (((SPEED) == GPIO_SPEED_FREQ_LOW) || ((SPEED) == GPIO_SPEED_FREQ_MEDIUM) || \ 279 ((SPEED) == GPIO_SPEED_FREQ_HIGH) || ((SPEED) == GPIO_SPEED_FREQ_VERY_HIGH)) 280 #define IS_GPIO_PULL(PULL) (((PULL) == GPIO_NOPULL) || ((PULL) == GPIO_PULLUP) || \ 281 ((PULL) == GPIO_PULLDOWN)) 282 /** 283 * @} 284 */ 285 286 /* Private functions ---------------------------------------------------------*/ 287 /** @defgroup GPIO_Private_Functions GPIO Private Functions 288 * @{ 289 */ 290 291 /** 292 * @} 293 */ 294 295 /** 296 * @} 297 */ 298 299 /** 300 * @} 301 */ 302 303 #ifdef __cplusplus 304 } 305 #endif 306 307 #endif /* __STM32F4xx_HAL_GPIO_H */ 308 309 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 310